In this article
A suitable adhesion promoter level comes from a controlled trial, not the highest dose. Define the control and dosage basis, compare clearly labelled dosage levels under consistent conditions, record adhesion, gloss and viscosity together, then validate a working range for the tested ink and substrate.
Why Does Adhesion Promoter Dosage Need a Controlled Trial?
A laboratory prints three samples at different promoter levels on the same film and gets three different adhesion results. The real question is which addition level, or band of levels, can be trusted in routine production.
Picking the strongest dose or a lone good sample rarely answers it. A controlled comparison against a defined reference helps isolate the dosage effect. Additional validation is needed to assess performance across different raw material lots and adhesion promoter application conditions.
This guide explains how to plan and interpret an ink adhesion promoter dosage trial without assuming a universal addition level. It refers to Tridev Group’s published product information for grade details. Trial conditions and acceptance criteria should follow the laboratory’s approved procedure.
Define the Adhesion Promoter Trial Objective and Control
Before weighing any sample, record the ink system, substrate, printing or application method and the performance the print must deliver. A trial of an adhesion promoter in printing inks for surface printed film differs from one aimed at lamination, so the objective shapes every later choice.
The control is the same ink without the trial adhesion promoter. Ideally, the control and all candidate samples come from one base ink batch, so batch variation is not mistaken for a dosage effect.
A control without the trial additive is not free of every additive. Its binder, wetting agents or an existing adhesion enhancer may already contribute to adhesion, so each should be documented and left in place, since removing one changes the base formulation.
If a current production ink is available, keep it as a separate reference: it shows where the trial stands against today’s product, a comparison the control alone cannot give.
Confirm the Ink Adhesion Promoter Dosage Basis
A dosage written as a bare percentage is incomplete, because the same figure gives very different additive masses on different bases.
Confirm both parts of the dosage instruction from the adhesion promoter supplier: whether the percentage is based on total ink weight or binder solids, and whether the additive quantity refers to the product as supplied or its active content.
Here, the specified basis mass is the mass of total ink or binder solids named in the instruction. The calculation is then direct:
Additive mass = Specified basis mass × Recommended dosage fraction
Where the instruction refers to active content, convert it to the mass actually weighed:
Supplied additive mass = Required active additive mass ÷ Active content fraction
A titanium content figure on any specification describes composition and should not be used as an active content fraction unless the supplier states so.
Also separate an addition to an existing batch from a percentage of the final mixture. Adding a mass calculated on the batch gives a slightly smaller share of the finished blend, so the record must state which convention applies.
Design a Printing Ink Adhesion Promoter Dosage Comparison
A practical layout compares the control with several addition levels chosen within the supplier’s permitted guidance. Neutral labels such as Control, Level A, Level B and Level C keep the plan clear and unbiased while levels are compared.
When working with Tridev Group grades, ask for the addition and mixing instructions at the enquiry stage and follow them identically for each sample. The plan should also specify:
- A documented formulation balance for every sample
- Comparable sample age at the time of application
- Replicate samples in line with the laboratory’s own procedure
If the selected adhesion promoter contains a carrier, increasing its dosage also changes the carrier contribution. Record any resulting changes in solvent balance, solids and viscosity. State which property is held constant and how, for example by reducing a matching solvent in the base.
Where the carrier itself could influence adhesion, a compatible carrier control may help separate its effect from that of the promoter. This step should follow supplier guidance and is not automatically required.
Keep Adhesion Promoter Application Conditions Consistent
Specimen preparation introduces variables that can mask real differences between levels. Control and document the following for every sample:
- Substrate type, batch and printing side
- Surface treatment condition, where relevant
- Ink application method and equipment
- Deposited film amount, or a controlled proxy for it
- Drying conditions
- Conditioning time before evaluation
- Test environment
A fixed equipment setting does not prove an equivalent result. The same applicator may deposit different film weights if viscosity or wetting differs between samples, so the deposit should be checked where possible.
No single drying temperature, treatment level or conditioning time suits every ink system and end use. Once chosen, these settings stay fixed across the control and every level.
Record Adhesion, Gloss and Viscosity in Adhesion Promoter Trials
Adhesion is only one of the properties a print must meet. Logging gloss and viscosity against the same trial ID lets the effect of each level be read as a whole.
| Trial ID and dosage basis | Adhesion result | Gloss result | Viscosity and measurement conditions |
|---|---|---|---|
| Control (no trial additive) | [Score and method] | [Value and geometry] | [Reading, method, temperature, sample age] |
| Level A ([Basis]) | [Score and method] | [Value and geometry] | [Reading, method, temperature, sample age] |
| Level B ([Basis]) | [Score and method] | [Value and geometry] | [Reading, method, temperature, sample age] |
| Level C ([Basis]) | [Score and method] | [Value and geometry] | [Reading, method, temperature, sample age] |
Adhesion needs a defined test method, consistent timing after printing and a fixed scoring scale. If a tape method is used, the tape type, application pressure, dwell time and removal procedure must be controlled.
Gloss readings are comparable only when geometry, backing and measurement position match. Record viscosity with its method, temperature and sample age; if it is adjusted before printing, log the original reading and the adjustment separately.
Visual observations such as haze, ink lift or uneven laydown support the measured results but are not numerical proof.
Interpret Adhesion Promoter Results and Validate a Working Range
Judge results against acceptance criteria fixed before testing, never criteria adjusted to suit the data. Useful questions include:
- Does each level improve on the control, and by how much?
- Are results repeatable across specimens?
- Do adjacent levels differ beyond the variation of the measurement method?
- Do gloss, viscosity or other required properties move outside their limits?
The response need not rise steadily with dosage. Adhesion may plateau or decline at higher levels while side effects on other properties grow.
An observed improvement shows what happened under those conditions; it does not prove a mechanism, which needs separate investigation.
A single successful level does not establish a working range. A range needs evidence that its boundaries and relevant intermediate points all remain acceptable.
When several levels pass, favour a band wide enough to tolerate expected weighing, batch and process variation, instead of defaulting to either end. Confirm it with independently prepared samples under relevant production conditions before routine adoption.
Conclusions on adhesion promoter use apply only to the tested ink, substrate and conditions. A new substrate or binder system calls for its own trial.
About Tridev Group as an Adhesion Promoter Manufacturer
Tridev Group, comprising Tridev Resins (India) Pvt. Ltd., Tridev Industries Pvt. Ltd. and Micro Resins Pvt. Ltd., manufactures and exports synthetic resins from Vapi and Dahej, Gujarat. Its range includes ketonic, polyvinyl butyral, polyamide, polyurethane and rosin modified resins for printing inks, paints and coatings.
Its adhesion promoters include TA-10 for flexo and gravure inks and TPI-02 for flexo inks and overprint varnishes. Formulators can share their ink system, substrate and trial requirements through the contact page, and request the latest technical data for the selected grade.
Conclusion on Adhesion Promoter Dosage Trials
The level adopted for production should be the one the evidence supports, recorded with its dosage basis and trial conditions so the result can be reproduced.
Teams evaluating an ink adhesion promoter for flexo or gravure systems can contact Tridev Group to discuss which grade, TA-10 or TPI-02, best fits their application.
Need Technical Information or a Product Quote?
Our team responds with specifications, samples and pricing for your application.


