In this article
The theoretical mixing ratio of a reactive polyamide resin is calculated using the epoxy EEW and hardener AHEW. Supplier recommendations establish the appropriate working ratio. This guide works through the calculation and explains how amine value, pack ratios and solvent content affect it, helping formulators set accurate ratios with Tridev Resins Trimide grades.
What Determines the Mixing Ratio of a Reactive Polyamide Resin?
A reactive polyamide resin, such as a Trimide grade from Tridev Resins, works as an reactive polyamide resin because its amine groups react with epoxide groups to build a crosslinked film. In polyamide cured epoxy systems, a figure read on the wrong basis or matched to the wrong epoxy can unbalance a batch before weighing begins.
What Are EEW and AHEW in a Reactive Polyamide Epoxy Hardener System?
Epoxy equivalent weight (EEW) is the mass of epoxy resin, in grams, that contains one equivalent of epoxide groups. A lower EEW means more epoxide equivalents per gram. For the same curing agent and target equivalent balance, this increases the calculated hardener requirement per 100 parts of epoxy resin.
Amine hydrogen equivalent weight (AHEW) is the mass of curing agent, in grams, containing one equivalent of reactive amine hydrogen. Use the supplier stated EEW and AHEW, noting whether each is a typical value or a specification range. Where ranges are supplied, confirm the calculation basis before setting a production ratio.
How Is a Polyamide Curing Agent Ratio Calculated from AHEW and EEW?
The theoretical amount of polyamide curing agent per 100 parts of epoxy resin comes from one formula: Hardener phr = (AHEW ÷ EEW) × 100. The result, expressed as parts per hundred resin (phr), gives one equivalent of amine hydrogen for every equivalent of epoxide, the point of balanced reaction.
The values below are hypothetical and do not relate to any Trimide grade:
| Hypothetical input | Value |
|---|---|
| Epoxy resin EEW | 190 g/eq |
| Curing agent AHEW | 95 g/eq |
| Calculated hardener requirement | 50 phr |
| For 100 g epoxy resin | 50 g hardener |
| Epoxy resin to hardener ratio by weight | 2:1 |
This result is a theoretical starting point; the supplier’s recommended use level and application testing establish the working formulation. Where the epoxy side is a blend of two resins or contains a reactive diluent, the EEW of the whole blend must be worked out from the equivalents each component contributes.
What Happens When Polyamide Cured Epoxy Is Mixed Off Ratio?
Insufficient or excess hardener can affect network formation in polyamide cured epoxy. The resulting changes in hardness, flexibility, adhesion and chemical resistance of epoxy polyamide coatings depend on the formulation, cure conditions and extent of the imbalance. Some only become apparent in service, when a ratio error is difficult to trace.
Why Does Amine Value Alone Not Establish the AHEW of a Reactive Polyamide?
Amine value is the specification most often quoted for a reactive polyamide. Use the amine value specification stated in the current Tridev Resins documentation for the selected Trimide grade. It measures titratable basicity in mg KOH/g but does not directly identify reactive amine hydrogen equivalents, so it is not interchangeable with AHEW.
Its practical role is quality checking of incoming batches, where results within the grade limit indicate consistent supply rather than a need to change the mixing ratio. For the AHEW of the selected Trimide grade, confirm the value directly with Tridev Resins rather than deriving it from amine value.
How Should Epoxy Hardener Mixing Ratios Be Read on a Data Sheet?
A data sheet may also express the ratio as a percentage of the total mix or as a pack ratio, such as 4:1 for Part A to Part B. A pack ratio requires particular attention because Part A may contain pigment, filler and solvent, so its epoxy content must be known before checking against phr.
Should Reactive Polyamide Resin Ratios Be Measured by Weight or by Volume?
The AHEW and EEW calculation always gives a weight ratio, because both equivalents are defined in grams. Volume ratios suit components dispensed by pump, measuring can or cartridge. Reactive polyamide hardeners and liquid epoxy resins often differ in density, so a ratio of 2:1 by weight should not be assumed to equal 2:1 by volume.
Any conversion should use density measured at the dispensing temperature. The viscosity stated for each Tridev Resins reactive polyamide grade helps production teams select suitable dispensing equipment, and periodic checks of dispensed component weights can help identify dosing discrepancies before they affect a full production batch.
How Do Solids Content and Supplied Form Affect a Polyamide Curing Agent Ratio?
A polyamide curing agent may be supplied neat or cut in solvent for easier handling and processing. Solvent adds weight without adding amine hydrogens, so the same hardener in solution has a higher effective AHEW than in its undiluted form, which makes the stated basis of any recommended ratio important.
If a hardener requirement is stated on a solids basis, weighing the same numerical amount of a solvent diluted hardener supplies insufficient active material. A ratio quoted as supplied, however, must not be corrected a second time for solvent, and the same rule applies equally to a solution grade epoxy.
How Can Formulators Verify a Reactive Polyamide Resin Ratio Before Trials?
Before the first trial batch, confirm these points with Tridev Resins for the chosen Trimide grade:
- The measuring basis of the recommended use level
- Which EEW, or which epoxy resin, the recommendation was built around
- The induction time and pot life that apply at that ratio
Evaluate the proposed ratio under the intended application and cure conditions, and follow supplier guidance for any comparison of alternative ratios. Record the approved formulation, component identities and measurement basis together on the batch sheet. A retained cured sample from the approved trial gives a physical benchmark for later batches.
Who Is Tridev Resins as a Reactive Polyamide Resin Supplier?
Tridev Resins, part of Tridev Group, is based at GIDC Vapi in Gujarat, India. Alongside its Trimide reactive polyamide grades, offered as an epoxy hardener for adhesives, coatings and grouts, it supplies synthetic ketonic, polyvinyl butyral, non reactive polyamide, polyurethane and rosin modified maleic resins.
Conclusion: How Can Epoxy Polyamide Coatings Teams Keep Mixing Ratios Consistent?
A reactive polyamide resin ratio works best when EEW, AHEW and measuring basis are treated as one linked set of inputs rather than separate figures. With R&D chemists owning the calculation and production supervisors owning the dispensing method, a Tridev Resins Trimide formulation has a consistent reference for every batch.
——————————————————–
Need Technical Information or a Product Quote?
Our team responds with specifications, samples and pricing for your application.


